manualshive.com logo in svg

DSC 3G2055, Руководство по установке, Страница: 28 / 52

Поделиться
Скачать
DSC 3G2055 Скачать руководство пользователя страница 28

28

with the same values. When operating in common receiver mode the Ethernet
Receiver 2 account code will be used for communications over Ethernet and Cellular.
NOTE: Do not program Ethernet Receiver 1 and Ethernet Receiver 2 to communicate

to same receiver.

[114] Ethernet Receiver 2 Remote Port

Default (0BF5/3061)

This Section is used to program the port number used by Ethernet Receiver 2. Set
the value of this port when your installation is located behind a firewall, and must be
assigned a particular port number as determined by your central station system
administrator. Valid range: 0000 - FFFF.
NOTE: Do not program Ethernet Receiver 1 and Ethernet Receiver 2 Port with the

same value.

[115] Ethernet Receiver 2 Local Port

Default (0BF9/3065)

Use this Section to program the value of the local outgoing port. You can set the
value of this port when your installation is located behind a firewall and must be
assigned a particular port number as determined by your network administrator. Valid
range: 0000 - FFFF. 
NOTE: Do not program Ethernet Receiver 1 and Ethernet Receiver 2 Port with the

same value.

[116] Ethernet Receiver 2 Domain Name

Default (  )

i

Programming this Section is 

not

  permitted on a UL/ULC listed system.

Enter the Domain Name as 32 Character ASCII.

E

THERNET

 O

PTIONS

[124] Ethernet Test Transmission Time

Default (9999)

Enter a 4 digit number (0000-2359) using the 24-hour clock format (HHMM) to set the
test transmission time of day. 
Valid range: 00 - 23 hours (HH) and 00 - 59 minutes (MM). Programming a value of
9999 will disable the test transmission time.
NOTE: The internal date and time will automatically be programmed when the unit

communicates with the primary receiver.

[125] Ethernet Test Transmission Cycle

Default (000000)

This value represents the interval between test transmissions, in minutes. Valid
range: 000000 - 999999 minutes. Once the unit has sent the initial periodic test
transmission, all future test transmissions will be offset by the programmed number
of minutes. See Sections [026] - [029].

NOTE: Minimum value is 000005 minutes. Programming an interval that is less than

5 minutes will disable test transmission.

C

ELLULAR

 R

ECEIVER

 1 O

PTIONS

[201] Cellular Receiver 1 Account Code

Default (0000000000)

The account code is used by the central station to distinguish between transmitters.
This account code is used when transmitting heartbeat signals to the central station
receiver. Signals received from the control panel will use the control panel account

Table 12: Ethernet Test Transmission Interval

Test Transmission Interval

Daily

Weekly

Monthly

Programmed Minutes

001440

010080

043200

Содержание 3G2055





















































Отзывы:

Нет отзывов