manualshive.com logo in svg

DryGair DG-X, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
DryGair DG-X Скачать руководство пользователя страница 40

Maintaining the Unit 
Daily Maintenance 
 

DryGair Energies Ltd

 .

 

34 

7. 

MAINTAINING THE UNIT 

The maintenance chapter provides instructions related to periodic 
maintenance and unit cleaning. 

Periodic cleaning and maintenance of the unit will ensure efficient and long-
term operation. 

 

Warning 

High voltage is present at points throughout the unit. Contact can result 
in injury or death. Before opening the unit electrical compartment, ensure 
you are familiar with the location of the external circuit breaker to the 
unit. 

 

 

Caution 

Avoid direct water contact with the unit sensors! 

Do not immerse them in water and/or spray water directly at them. 

 

7.1 

Daily Maintenance 

Perform the following every day: 

•

 

Visually inspect the unit, verifying the unit is operating properly, and 
noticing if there is anything unusual. 

•

 

Clean the unit and its surroundings from any foreign material. 

7.2 

Monthly Maintenance 

 

Warning 

Before performing the following procedures, power down the unit and 
disconnect the power cord. 

 

Perform the following monthly: 

•

 

The daily maintenance. 

•

 

Check to see if there are any oil stains/residues. If found, check to see the 
origin and contact your local DryGair representative. 

 

Warning 

Do not steam-clean the heat exchanger coils. 

 

Содержание DG-X























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды