background image

- 18 -

 

 

Adjusting the thermostat knob to the left backstop  does not mean permanent shutoff of the 
heating  element.  When  the  heater  is  in  use  without  blocking  the  daily  rate,  we  do  not 
recommend  the  temperature  to  be  set  above  55 

°C.  Select  the

 

„OPTIMUM“ 

symbol  as  the 

maximum. 

4

 

IMPORTANT NOTICES 

4.1

 

INSTALLATION REGULATIONS 

-

 

Without  a  confirmation  of  performed  electrical  installation  issued  by  an  authorized  company, 
the warranty certificate shall be void. 

-

 

Check and exchange the Mg anode regularly. 

-

 

You have to apply for approval of a local power supplier to connect the heater. 

-

 

No stop valves can be put between the heater and the safety valve. 

-

 

If the overpressure in the water main exceeds 0.48 MPa, a pressure control valve must be mounted 
before the safety valve. 

-

 

All hot water outputs must have a combination faucet. 

-

 

Before  filling  the  heater  with  water  for  the  first  time,  it  is  recommended  to  fasten  the  flange 
connection nuts of the tank. 

-

 

It is not allowed to handle the thermostat, aside from temperature resetting with a control button. 

-

 

All electric installation handling, adjustment and replacement of the regulation elements shall only 
be performed by an authorized service company. 

-

 

The thermal fuse must not be turned off!

 In case of thermostat defect, the thermal fuse interrupts 

electric power input to the heating element if the water temperature in the heater exceeds 90 °C.

 

-

 

If you don't use the heater (hot water tank) for longer than 24 hours, or if the facility with heater 
is unattended, close the cold water inlet to the heater. 

-

 

The  heater (hot water tank)  shall be  used exclusively in accordance  with the  conditions specified 
on the performance plate and in the instructions for electric wiring.  

-

 

The recommended operating pressure in the hot water circuit is 0.48 MPa. At the hot water discharge 
we recommend that a reverse flap and an expansion tank are installed (at least 4 % of hot water 
volume in the manifold) to eliminate reverse pressure shocks. 

 
 

Both  the  electric  and  water  installation  must  follow  and  meet  the  requirements 
and regulations relevant in the country of use!

 

 
 

4.2

 

TRANSPORT & STORAGE INSTRUCTIONS 

The device shall be transported and stored in dry place and protected from weather effects with temperature 
range from -15 to +50 

°C. During loading and unloading the instr

uctions stated on the packaging shall be 

observed. 

 

 

Содержание OKHE ONE/E 120




















Отзывы: