Draper Tools Limited, Hursley Road,
Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: [email protected]
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Helpline for details of an agent in your local area.
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
CONTACTS
YOUR DRAPER STOCKIST
TACH0318
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
FIG.5
ASSEMBLY AND OPERATION
MAINTENANCE
INSTALLING/ADJUSTING THE
TEXTURE/PATTERN CONTROL – FIG.5
– The
guide
pointer
is fixed onto machine via
the protruding threaded end of the pressure bar.
– Use the washer
and wing nut
to secure
the guide pointer in place.
– To increase the pressure on the tines of the roller,
turn the guide pointer downwards incrementally
using the notched scale
.
– The
lower the pointer is positioned on the scale,
the more pressure is exerted onto the roller tines
by the bar.
OPERATION
Droplets of workable cement-rich mortar are flicked onto the work surface by rotating sprung
tines located on the horizontal roller. The tines are always partially immersed in the mix.
As a rule, the machine is used in conjunction with manufacturer’s pre-prepared mixes. When
using such mixes, always follow the manufacturer’s supplied guidelines and instructions.
Best results are obtained by using small quantities more frequently. Always use materials within
one hour of mixing.
Method of application – 1st layer:
Keeping a minimum distance of 500mm/20" away from the
work surface, allow a full spread of material from the machine
(take special care at this point if
working on scaffolding).
Regulate the turning speed of the drive handle to ensure maximum output of material but at the
same time obtaining a thin surface covering.
Following layers:
Incrementally build up the texture over the initial ‘thin’ covering. The turning
speed of the drive handle can be reduced slightly, allowing for increased pick up of material.
Move closer to the work area as the turning speed is reduced.
Keeping the handle turning, continue building up the textured finish. A total thickness of 6 –
8mm/ 1/4" – 5/16" will give the optimum ‘honeycombed’ finish.
Replacement roller.
02250
PTFR
Item
Stock No.
Part No.
- 5 -
It is vital that the machine is thoroughly washed and cleaned during any break in the work and
also at the end of the working session.
Follow the previous assembly instructions in reverse to disassemble the machine for cleaning
and storage. Replacement consumable parts listed below can be obtained for this machine
through the usual Draper stockists.
DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In
all
circumstances:
●
Do not dispose of with domestic waste.
●
Do not incinerate.
REPRESENT
A
TION ONL
Y
NOT ACCURA
TE FOR COLOUR
USE COLOUR REFERENCES SPECIFIED ON AR
TW
ORK
Artist: .............................
Date: ...............
Proofer:
...........................
Date:
...............
Database: ........................
Date: ...............
2nd INTERNAL PROOF
Cyan
Magenta
Ye
llo
w
Black
Draper Blue
Draper Green
Draper Red
Draper Black
Clear V
arnish
06/03/18
Chris Hoar
e
Buying: ..........................
Date: ...............
Sales: ............................
Date: ...............
2nd EXTERNAL PROOF
Amend as Marked - Studio Re-proof Only
Fully Approved
Amend as Marked - Re-proof
B
U
YING:
Please tic
k 1
of
the
belo
w
options
IF YOU SIGN, PLEASE CHECK;
Pack type & style, all content, bar code printout
& note proof size (artwork to be sent @ 100%).
TYROLEAN
FLICKER MACHINE
02171
