Copyright © 2002 Draper, Inc.
Form ArtisanEV_Inst02
Printed in U.S.A.
Installation/Operating Instructions
Artisan/Series E & V Electric Projection Screen by Draper
Caution
➀
Read instructions through completely before proceeding.
➁
Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂
Screen should be accessible for complete removal should fabric become
damaged or should other service be required.
➃
Screen should be installed level (using a carpenter’s level).
➄
Nothing should be fastened to screen dowel or viewing surface.
➅
Operating switch(es) packed separately in screen carton. Do not discard
with packing material.
➆
Screen operates on 110-120v, 60 Hz. current.
NOTE
: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
General:
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in case.
Take care to install wall/ceiling electrical box and conduit so they will be fully
concealed by the screen case after installation.
The Artisan’s furniture-quality case should always be handled carefully to
avoid scratching and protect its finish.
Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface will
not cause case to work loose or fall. Installer must insure that fasteners used
are of adequate strength and suitable for the mounting surface chosen.
Wall Installation:
Mount 2, 3, or 4 aluminum brackets provided on the wall at desired height,
using toggle bolts provided or other appropriate fasteners. Verify that they are
in line and level to fully engage matching brackets pre-installed on back of
screen case. When screen is set on brackets, pull down gently to ensure that
it is snug and secure.
Ceiling Installation:
Install through the two
5
/
16
" diameter mounting holes at each end of the screen
case, using appropriate fasteners.
Electrical Connections
Screen operates on 110-120v, 60 Hz. current.
Junction box is located in the left end of case. It is accessible through bottom
of case when hinged door is opened. Junction box contains red, black and
white pigtail leads and green internal ground wire, per wiring diagram on
reverse.
Wall or ceiling electrical box should be installed so as to be fully concealed by
screen case after installation. Conduit openings are covered by plastic caps
Operation
Before operating screen remove tape securing fabric and dowel to roller. If
viewing surface hangs out of case 8
" or 9", tape has probably been broken by
rough handling in shipment, allowing surface to “unwrap” one turn about the
roller. Manually wrap fabric back around the roller without turning the roller
itself.
110-120v Single Station Control —
3-position up-off-down switch permits
operation to be stopped at any point. Factory adjusted limit switches
automatically stop screen when fully down or fully up.
110-120v Multiple Station Control
—Switches are similar in appearance to
110-120v Single Station Control. Screen stops when switch is released and
may be restarted in either direction. Factory adjusted limit switches stop
screen automatically when fully up or fully down.
24v Control —
Three-button up-stop-down switches stop at any point
desired, operate in any sequence. Factory adjusted limit switches
automatically stop screen when fully up or fully down.
Key Operated Switching —
Two kinds of key-operated switches are
optionally available with this unit.
➀
The key-operated power supply switch controls power to the screen and
switches. When it is “off”, the switches will not operate screen. Key may be
removed from the switch in either “on” or “off” position.
➁
A three-position key switch permits the screen to be operated directly by
key. In this case, the screen’s operator must always have a key.
Adjustments
Screen has been factory set and should not normally require further
adjustment. However, if you desire to change the “up” and “down” stopping
positions, proceed as follows:
CAUTION:
Be sure all switches are in “off” position before adjusting limit
switches. Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
Adjusting “fully up” position —
“Up” stopping position may be adjusted by
turning the yellow limit switch adjustment socket. The yellow socket is located
on left end of screen roller and is accessible to a screwdriver/Allen wrench
(4mm or
5
/
32
"). Turning the socket counterclockwise will allow the viewing
surface to retract farther into the case. Turning it clockwise will cause the
surface to stop farther out of the case. One full revolution of the socket will
alter the stopping position of the viewing surface by approximately 1½".
Adjusting “fully down” position —
“Down” stopping position may be
adjusted by turning the white limit switch adjustment socket. The white socket
is located on the left end of screen roller and is accessible to a screwdriver/
Allen wrench (4mm or
5
/
32
"). Turning the socket counterclockwise will allow the
viewing surface to run farther down. Turning it clockwise will shorten the
viewing surface, causing it to stop in a less extended position. At no time
should viewing surface be unrolled enough to expose any part of screen roller.
If you encounter any difficulties installing or servicing your Artisan
screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765)
987-7999, fax (765) 987-7142, or e-mail [email protected].
Z-brackets supplied
with screen for
wall mounting.
Hardware by others.
Z-brackets on
rear of case
Screen Case
Knockout for rear
conduit connection
Left end
5
/
16
" holes for
ceiling mounting.
2 each end.
Wall
Knockout for top
conduit connection
(to be removed for installation). Opening for ceiling mounting is located in top,
2
7
/
8
" from the end and 2½" from the back of the case. Opening for wall
mounting is in back, 2
7
/
8
" from the end and 2¾" from the top of the case.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire connecting screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with attached wiring diagram, and wiring should comply with National and
local electrical codes.
All operating switches should be “off” before power is connected.
Please Note: Instructions for adjusting Draper’s Tab-Tension System for
Series/V screens are on page 2.
