Dräger Polytron 7500 Скачать руководство пользователя страница 26

Страница: 26 / 72

Maintenance

Page 26 of 72 Pages

9023927 - 2nd edition - May 2007

Replacing the pyrolysis oven

●

Disable the supply voltage.

●

Remove the cover of the Polytron 7500. To do this

gently pull apart the cover on both sides and

lift upwards.

Only use a pyrolysis oven, which is suitable for use with the Polytron 7500 with
the deﬁned gas type, see “Order List” on page 64.

●

Disconnect the three electrical connections of the pyrolysis oven on the printed
circuit board.

●

Loosen the two screws for fixing on the rear side – do not unscrew completely.

●

Remove the pyrolysis oven upwards from the holder.

●

Remove the hoses to the pyrolysis oven and connect to the new pyrolysis oven at
the same position.

●

Insert the new pyrolysis oven from above into the holder and tighten the two
screws.

●

Reconnect the three electrical connections of the pyrolysis oven.

●

Refit the cover of the Polytron 7500.

●

Switch on power supply.

●

Wait until the sensor has fully warmed up.

— The Polytron 7500 is ready for use again.

Attention!
When the unit is opened

there is the danger of scalding yourself on hot

parts of the Polytron 7500.

0322392

7_1

.eps

0332392

7_1

.eps

Содержание Polytron 7500









































































Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды

Dräger Polytron 7500, Инструкция по эксплуатации

Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды