manualshive.com logo in svg

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 69 / 308

Поделиться
Скачать
Dräger Narkomed 2B Скачать руководство пользователя страница 69

NM2B

REPLACEMENT PROCEDURES (continued)

4.12

Vaporizers

Each vaporizer is held to the machine by two metric sized hex screws. These
screws are accessible at the back of the vaporizer mount, below the interlock
mechanism as shown in Figure 4-12. Before removing a vaporizer from the
machine, it must be completely drained and dried in accordance with the
procedure given below. Be sure to have a suitable packing or storage container
available in which to place the vaporizer.

CAUTION:

The following steps must be performed in the sequence given.

4.12.1

Set the System Power switch to

ON.

4.12.2

Set all vaporizer handwheels to their Zero or OFF position.

WARNING:

Do not inhale anesthetic vapors as this could
result in personal injury.

4.12.3

Remove the filler and drain plugs, and drain the vaporizer into a
suitable container. Dispose of the residual agent in an approved
manner.

4.12.4

Turn the vaporizer handwheel to the maximum concentration setting.

4.12.5

Set the oxygen flow to 10 l/min. for at least 20 minutes.

WARNING:

This procedure must be performed in a well
ventilated area and without personnel present.

4.12.6

Turn the vaporizer handwheel to 0 (zero), and replace the filler and
drain plugs.

4.12.7

Turn the oxygen flow off, and set the System Power switch to

STANDBY.

4.12.8

While holding the vaporizer, remove the mounting screws and
carefully separate the vaporizer from the machine. Note the
arrangement of gaskets so that the replacement vaporizer can be
installed in the same manner.

4.12.9

Place the vaporizer in a suitable container for transport or storage.

WARNING:

Do not tilt a vaporizer that contains anesthetic
agent more than 45 degrees. Failure to observe
this

precaution

will

render

the

handwheel

calibration invalid.

Rev. A

4-37

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Отзывы:

Нет отзывов