Dräger Narkomed 2B Скачать руководство пользователя страница 40

Страница: 40 / 308

REPLACEMENT PROCEDURES (continued)

NM2B

4.3

Cylinder Cutoff Valves (Canada)

Access to the cylinder cutoff valves requires removal of the table top from the
anesthesia machine. Figure 4-3 shows the locations of the O

, Air or 3rd gas,

and N

O cutoff valve assemblies. The instructions apply to all three assemblies.

On earlier machines the tubing arrangement may be slightly different from
that illustrated.

NOTE: Replacement of the O

Cutoff Valve Assembly shall be performed every

24 months. Documentation shall be created by the service person and a copy
distributed to the owner institution. Testing of the O

Cutoff Valve shall be

performed at each PMS. (Perform the flow test given at the end of the
following procedure)

4.3.1

Disconnect all pipeline hoses and set the System Power switch to ON.

4.3.2

Close all cylinder valves except the O

valve.

4.3.3

Set the oxygen flow to 5 liters per min.

4.3.4

Open the other gas flow control valves to drain pressure from the
system.

4.3.5

Close the O

cylinder valve, and close the flow control valves. Press

the O

Flush valve to drain oxygen pressure from the system.

4.3.6

Set the System Power switch to

STANDBY

4.3.7

Remove the screws holding the table top to the machine and lift out
the table top.

4.3.8

Remove the top drawer from the cabinet and pull the writing or
keyboard tray out to its fully extended position.

4.3.9

Disconnect the compression fittings indicated at points marked

the illustration.

4.3.10

Cut the tie-wrap clamp and disconnect the flexible tubing from the
cutoff valve assembly at the point marked

on the illustration.

NOTE:

On later machines with assemblies that have brass fittings instead
of nylon, the flex tubing is attached with a press-on hose clamp
instead of a tie strap.

4.3.11

Remove the cylinder cutoff assembly.

4.3.12

Connect the flexible tubing to the replacement cutoff valve assembly
and secure it with a new tie-wrap clamp.

Rev. D

4-8

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 40 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: