Dräger Narkomed 2B Скачать руководство пользователя страница 238

Страница: 238 / 308

PMC PROCEDURE (continued)

NM2B

6.30 OXYGEN FLUSH VALVE

Turn the System Power switch to STANDBY.

6.30.1

Press and release the O

FLUSH button.

6.30.2

Does the flow of oxygen stop immediately? __ (Y)

6.30.3

Close the APL valve.

6.30.4

Connect a 12-inch hose to the inspiratory valve.

6.30.5

Set the Man/Auto selector to BAG.

6.30.6

Occlude the bag mount.

6.30.7

Insert the sensor from a calibrated O

Med into the valve dome adapter

on the inspiratory valve.

6.30.8

Close all flow control valves.

6.30.9

Press the O

FLUSH button.

( )

6.30.10

What is the O

concentration after the value stabilizes?___%O

(97-100)

6.30.11

Remove the O

Med sensor and install the plug.

6.30.12

Remove the test minute volumeter (P/N 2212300) from the absorber and
connect it to the common gas outlet, using Fresh Gas Outlet Volume
Test Device (P/N S010158).

6.30.13

Press and hold the O

FLUSH button for 15 seconds; multiply the value

by 4.

( )

6.30.14

What is the oxygen flush flow rate? ___l/min. (45-65)

6.30.15

Remove the test minute volumeter and test fixture, and reconnect the
fresh gas hose.

6.30.16

Turn the System Power switch to ON.

Rev. Y

6-60

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 238 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: