Dräger Narkomed 2B Скачать руководство пользователя страница 234

Страница: 234 / 308

PMC PROCEDURE (continued)

NM2B

6.25B

BELLOWS: PEDIATRIC INTERNAL - if applicable

6.25B.1

Set the ventilator frequency to 10 BPM.

6.25B.2

Set the I:E Ration to 1:2.

6.25B.3

Turn the ventilator ON.

6.25B.4

Adjust the Inspiratory Flow control on the ventilator to Medium.

6.25B.5

Set the O

to 3 l/min.

6.25B.6

Occlude the 15mm patient side of the Y-piece and fill the bellows by
pressing the O

Flush button.

6.25B.7

Observe the absorber breathing pressure gauge as the ventilator cycles.

6.25B.8

What is the pressure when the bellows completes its downward travel?
___cmH

O >30

6.25B.9

What is the pressure when the bellows completes its upward travel?
___cmH

≤

6.25B.10 Install a 3 L breathing bag onto the patient circuit Y-piece.

6.25B.11 Fill the bellows by pressing the O

Flush button.

6.25B.12 Adjust the O

flow to 10 l/min.

( )

6.25B.13 What is the PEEP? ___cmH

O (

≤

6.25B.14 Adjust the O

flow to 500 ml/min.

6.25B.15 Adjust the inspiratory flow control until the bellows collapses entirely.

( )

6.25B.16 Does the ventilator deliver the full tidal volume during 5 consecutive

cycles? ___(Y)

6.25B.17 Set the ventilator frequency to 20 BPM.

6.25B.18 Adjust the O

flow to 5 l/min.

6.25B.19 Adjust the inspiratory flow control until the bellows collapses to the 100

ml mark on the pediatric bellows assembly.

Rev. Y

6-56

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 234 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: