Dräger Fabius 4116029 Скачать руководство пользователя страница 319

Страница: 319 / 328

6-1

Cop

ight

2000 Dr

aeger

edical,

sec6_f

aul

tca

usrem

.fm

6.0 Fault-Cause-Remedy

Fault

Cause

Remedy

A continuous audible
alarm is given. No
visible alarm appears
on the display.

Fabius is not connected to
mains power supply.

The rechargeable
batteries are flat.

Machine fault.

Connect Fabius to mains power
supply.

Recharge the batteries.

Inform DrägerService.

APNEA PRESSURE

Inappropriate fresh-gas
supply.

No ventilation.

Leak in hose system.

Ensure appropriate fresh-gas
supply.

Check hose system.

APNEA VOLUME

No ventilation

−

no expired

volume for 15 seconds.

Inappropriate fresh-gas
supply.

Kinked hose.

Leak in hose system.

Check ventilator.

Ensure appropriate fresh-gas
supply.

Check hose system.

APNEA PRESS OFF

The lower alarm limit for
the airway pressure (Paw)
is off in the IPPV mode.

Switch on the lower alarm limit for
the airway pressure (Paw).

BATTERY LOW

The battery voltage of the
uninterruptible power
supply (UPS) is too low.

Recharge the batteries of the
UPS by running Fabius from the
mains power supply for four
hours.

BATTERY POWERED

Fabius is not connected to
mains power supply
(Fabius is powered from
the batteries (UPS)).

The mains power supply
failed.

Connect Fabius to mains power
supply.

Check the mains power supply.

CHECK BATTERY

The backup battery is not
functional.

Replace fuse.

Inform DrägerService.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 319 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: