manualshive.com logo in svg

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 17 / 328

Поделиться
Скачать
Dräger Fabius 4116029 Скачать руководство пользователя страница 17

Fabius

®

Function Description

 

2-9

Cop

yr

ight

 2000 Dr

aeger

 M

edical,

 In

c.

sec2_f

uncdescri

p_b

.fm 

5

Function Description of the Gas Box

The supply gases flow through the built-in filters of the compressed-gas connections 
and are then available at the pressure gauges. The pressure gauges indicate the 
current pressure of the supply gases. The non-return valves prevent a reverse flow. 
The pressure of the supply gases is reduced by pressure regulators. The 
low-pressure supply gases then flow to the flowmeter block. As soon as the O

2

 supply 

gas has reached a sufficient pressure, it flows through the spring-loaded non-return 
valve RV 1 and fills the reservoir.

If the O

2

 supply fails or if the pressure of the O

2

 supply gas decreases below a certain 

value, the 2-way valve switches over. The gas stored in the reservoir flows through the 
2-way valve and the injector and activates the whistle (audible O

2

-failure alarm).

Fig. 8:

Function diagram of the gas box (3-gas version), part 1

O2

N2O

reservoir

injector

O2 flush

non-return valves

whistle

to the flowmeter

to the flowmeter

to the 
anesthetic 
vaporizer

pressure 
gauges

pressure regulators

filter

gas box

AIR

to the flowmeter

suction ejector

filter

N2O

O2

RV1

2-way valve

filter

su

pp

ly gas

es

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Отзывы:

Нет отзывов