DPtech LSW3003 Series Скачать руководство пользователя страница 13

Страница: 13 / 39

DPtech LSW3003 Series Industrial Ethernet Switch Installation Manual

Chapter 1 Product Introduction

Attribute

Description

Interface

speed

and

negotiation mode

10Mbps, half / full duplex

100Mbps, half / full duplex

Medium

and

maximum

transmission distance

Support 100m transmission distance

Interface standard

IEEE 802.3i

、

802.3u

、

802.3ab

1.4.3 10/100/1000Base-T Ethernet interface

1.Gigabit Ethernet interface properties

Table1-3

Gigabit Ethernet interface property table:

Attribute

Description

Connector Type

RJ45

Interface standard

MDI/MDIX auto-negotiation

Supported frame format

Ethernet_II

Ethernet_SNAP

Interface

speed

and

negotiation mode

10Mbps, half / full duplex

100Mbps, half / full duplex

1000Mbps, half / full duplex

Medium

and

maximum

transmission distance

Support 100m transmission distance

Interface standard

IEEE 802.3i

、

802.3u

、

802.3ab

2.Ethernet interface (RJ45 connector)

By using of the 5 categories or above 5 categories twisted pair cable to connect Ethernet, LSW3003

series Ethernet switch interfaces (10/100/1000M) adopt RJ45 connector and support MDI/MDIX

auto-negotiation. When you use the interfaces, please adopt 5 categories twisted pair cable and RJ45

connector to make network cable..

Содержание LSW3003 Series








































Результаты поиска

Содержание LSW3003 Series

Отзывы:

Бренды по названию

Популярные бренды

DPtech LSW3003 Series, Руководство пользователя

Результаты поиска

Содержание LSW3003 Series

Отзывы:

Бренды по названию

Популярные бренды