Dover Petro Vend FSC3000 Скачать руководство пользователя страница 42

Страница: 42 / 79

commands. For more information refer to the

M00-051.00 Command-Line Configuration Guide

2.7.3 FSC3000 Ethernet Port Setup

Before connecting to the FSC via its Ethernet adapter for card management and polling, you must configure
the Ethernet device.

Connecting the FSC to the Network

1. Before attempting to run the configuration utility, connect the FSC to the network using a standard

CAT5 network cable.

2. Remove the FSC power cable.

3. Connect one end of the cable to the device that provides an entry point into the network.

4. Connect the other end to the port label “E-NET” on the back of the FSC.

5. Plug the FSC power cable into the controller.

Configuring the FSC IP Address

ARTWare contains the software needed to configure the IP address of the Fuel Site Controller’s network
adapter. ARTWare can be downloaded from the OPW-FMS website at

https://www.opwglobal.com/opw-

fms/tech-support/software/other-software-downloads

See

"PV380 DigiServe & PV384 Lantronix Boards" on page 16

for information on what main board is

installed in your FSC3000.

Instructions for IP address configuration with the PV384 Lantronix board can be found in the "Lantronix
Device Finder" file found at

https://www.opwglobal.com/opw-fms/tech-support/software/other-software-

downloads

Instructions for IP address configuration with the PV380 Digi board are as follows:

1. Download the "Digi Device Discovery" file found at

https://www.opwglobal.com/opw-fms/tech-

support/software/other-software-downloads

2. In this folder is the program called “digiserve.exe”.

3. Run this application to configure the device’s IP address.

M1700 FSC3000 Installation Manual | Dover Fueling Solutions

Содержание Petro Vend FSC3000
















































































Результаты поиска

Содержание Petro Vend FSC3000

Отзывы:

Похожие инструкции для Petro Vend FSC3000

Бренды по названию

Популярные бренды

Dover Petro Vend FSC3000, Руководство по установке

Результаты поиска

Содержание Petro Vend FSC3000

Отзывы:

Похожие инструкции для Petro Vend FSC3000

Бренды по названию

Популярные бренды