Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 146

background image

Page 122 of 145

www.opwglobal.com

Connecting Directly via Crossover Cable

To connect to the console directly using a crossover cable, connect a
crossover cable from a PC directly to the SiteSentinel® iSite



Ethernet

port. Once this is done, the user’s PC will come up with a message
stating “limited or no connectivity.”

This is normal

. Once the cable is

connected, the user can log into the SiteSentinel® iSite



and go the

settings>system>networking to the SiteSentinel® iSite



IP address.

Once the IP address is found, enter that IP into the address bar of the
Internet browser. This should bring up the SiteSentinel® iSite



login

screen. The user may now login and explore/configure the
SiteSentinel®

iSite™.

If the SiteSentinel® iSite



or PC is setup to static IP, it must be

either changed to DHCP or set the PC to 1 IP below or above the
SiteSentinel® iSite™ IP address in order to connect.

Error: Limited or No Connectivity

Once the IP address is found and recorded, enter this IP address into
the  address  bar  on  Internet  Explorer  and  press  Enter  to  access  the
page.  This  will  load  the  login  screen  for  the  console.  Once  logged  in,
you  will  have the  same  access  as  if  you  were  pressing the  screen  on
the console.

Not all Utilities functions are available with a remote connection.

Connecting USB Keyboard

If  you  do  not  want  to  use  the  on-screen  keyboard  for  configuring  the
system  you  can  connect  a  USB  keyboard  to  the  system  for
configuration  purposes.  Plug  in  the  USB  keyboard  to  one  of  the
external USB ports for instant use of the keyboard.

There is a PS2 port on the inside of the console if you do not have a
USB keyboard available. See Appendix J: Console Boards for the
location of the port. In most cases the system will need to be
rebooted to recognize a keyboard plugged into this port.

Other connections used for polling POS information:

•

via FSC3000



passthru 20-1613

•

via System2



passthru 20-1456

•

direct serial 20-1520-05

«
...
120
121
122
123
124
...
»

Содержание OPW SiteSentinel iSite



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для OPW SiteSentinel iSite

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Oakton Страницы: 69

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 2

Бренд: NanoPhotometer Страницы: 133

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: Yamaha Страницы: 84

Бренд: ZHYQ Страницы: 6

Бренд: JENCO Страницы: 13

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: SKF Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды