Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 370

Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 147

Operating Instructions

Machine Description

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 147 / 370

Information

Observe the following points when you enter the password:



The background color of the input line changes from red to white as

soon as the required minimum number of characters is entered.



A password must be at least six characters long. It must contain num-

bers and at least one capital and one small letter, that may be in any
sequence.



The validity time of a password can be restricted if necessary.



An expired password must be replaced with a new one.

4.9.1

Logging off at the touchscreen

>

To log off, press the login button in the bottom right corner of the
touchscreen. Most buttons and displays are now locked. This shows
with a dimmed gray display.

The system logs off the user automatically when the touchscreen is not
used for a specified time after login.

The user is logged off automatically when the touchscreen is switched off
(together with the printing system).

Each user can manually lock the touchscreen at any time (for example to
prevent any intervention from unauthorized persons during his/her ab-
sence).

The currently running printing operation is not influenced by logging in/off.
The printer retains its current state.

«
...
145
146
147
148
149
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды