Dover MagLink LX4 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 63

background image

Section 3 Introduction

This manual was prepared in accordance with IEC 82079-1 standards. “Preparation of instructions for use -
Structuring, content and presentation - Part 1: General principles and detailed requirements and according to
the ATEX Directive 2014/34/EU concerning equipment and protective systems intended for use in potentially
explosive atmospheres."

This manual gives all necessary information about the configuration of the MagLink LX4 console.

IMPORTANT:

This manual must be used together with the related product manuals:

M2050-EU MagLink LX4 Installation Manual
M2052-EU MagLink LX4 User Manual

You must install the console as shown in the M2050-EU MagLink LX4 Installation Manual,
configure the console as instructed in this manual and use the console in the field as shown in
the M2052-EU MagLink LX4 User Manual.

WARNING:

This device must not be discarded with household waste. This

device is labeled in accordance with European Directive 2012/19/UE
concerning used electrical and electronic appliances (waste electrical and
electronic equipment – WEEE).

This guideline gives the methods for the return and recycling of used
electronic devices as applicable throughout the EU. To return your used
device, use the return and collection systems available to you.

The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, heat above 50°C or incinerate.

The table that follows lists reference data of the manufacturer:

Data

Description

Name

START ITALIANA S.r.l.

Address

Via Pola 6

20813 Bovisio Masciago (MB)

Italy

Telephone

+39 0362 1581465

Fax

+39 0362 1581464

Website

www.startitaliana.com

e-Mail

[email protected]

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 8

«
...
6
7
8
9
10
...
»

Содержание MagLink LX4
































































Отзывы:

Нет отзывов

Похожие инструкции для MagLink LX4

Бренд: Oakton Страницы: 4

Mentor Visual iQ

Бренд: GE Страницы: 2

Бренд: WattNode Страницы: 57

Бренд: Kanomax Страницы: 31

Бренд: Hach Страницы: 196

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

ORBISPHERE 3624

Бренд: Hach Ultra Страницы: 12

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

Бренд: Burkert Страницы: 192

Бренд: Magnet-physik Страницы: 32

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: TAC Страницы: 28

Бренд: E Instruments Страницы: 2

Бренд: Xylem Страницы: 10

Бренд: Lasertec Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды