Dover MagLink LX4 Скачать руководство пользователя страница 7

Страница: 7 / 63

Section 2 General Warnings

Carefully read the instructions in this manual before you do the installation procedures.

Only approved persons are permitted to install this equipment and configure the console.

The manufacturer is not responsible for operations that are not included in this manual.

The manufacturer is not liable in regards to competent bodies for changes to the equipment and software that
are not approved.

In case of failure or defect, refer directly to an authorized service provider or manufacturer.

The manufacturer is not liable for injury and/or damage to persons and/or property and/or pets caused by the
failure to obey safety instructions.

All approved personnel must know all safety requirements in this manual, the configuration manual and the
user manual.

Refer directly to an approved service provider or manufacturer for questions about the operation of the
equipment.

IMPORTANT:

You must read and obey all safety instructions in this manual before you use

this equipment.

WARNING:

Incorrect use of this equipment that does not agree with the

instructions in this manual can cause a risk to safety.

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 7

Содержание MagLink LX4
































































Результаты поиска

Содержание MagLink LX4

Отзывы:

Похожие инструкции для MagLink LX4

Бренды по названию

Популярные бренды

Dover MagLink LX4, Руководство по настройке

Результаты поиска

Содержание MagLink LX4

Отзывы:

Похожие инструкции для MagLink LX4

Бренды по названию

Популярные бренды