Dover MagLink LX4 Скачать руководство пользователя страница 23

Страница: 23 / 63

Field

Description

Connection

Select the type of connection:

None

: If no device communicates with the console.

Serial

: If a serial RS232 connection is made between the POS/FCC and the console.

TCP/IP

: If a TCP-IP connection is made between the POS/FCC and the console.

Sales

Click

YES

if the POS/FCC will transmit the dispenser sales transactions to the console. The Gilbarco

BCD protocol is supported for this function. Note, that only one connection at a time can support the sales
transactions.

Protocol

Select one of the two

Gilbarco

: To permit the GVR TLS350 protocol commands.

DOMS OPC

: To permit the DOMS OPC protocol commands.

Port

If serial communication was selected above, select which serial port will be used (COM1 or COM2).
If TCP-IP communication was selected above, configure the TCP-IP port that to be used.

Baud rate /
Parity / Data
bits / Stop bits

Theses fields are in operation if serial communication has been selected. Configure the settings for the
serial ports.

Enable
Gilbarco Set
Commands

Select this button for a range of GVR TLS350 set commands to be used.

Printer
Connection

Select:

None

: If no printer is connected

USB

: If a printer is connected through the USB port.

COM1/COM2

: If a printer is connected to the serial port (baud rate for the printer should be set to

9600 bps). Note that this is necessary for the fields to become available if the serial ports have not been
configured for POS/FCC communication.

Click

Save

and

Apply settings to console

when you complete the

Protocols

tab configuration.

6.1.4 Tank Group

NOTE:

The number of tanks are configured in the Site Info tab. Tank parameters are

configured in Tanks setup from the Main Menu.

This tab is used to make Siphon (Manifold) groups.

IMPORTANT:

Tanks in a Siphon (Manifold) group must contain the same product.

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 23

Содержание MagLink LX4
































































Результаты поиска

Содержание MagLink LX4

Отзывы:

Похожие инструкции для MagLink LX4

Бренды по названию

Популярные бренды

Dover MagLink LX4, Руководство по настройке

Результаты поиска

Содержание MagLink LX4

Отзывы:

Похожие инструкции для MagLink LX4

Бренды по названию

Популярные бренды