Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 136

background image

Issued May 2020
Lift Arm

Copyright 2020, Heil Environmental

Printed in the U.S.A.

Lift Arm

50

UNIVERSAL BELT AND TRI-CUFF GRABBER ADJUSTMENTS

A. 60-90 Gallon Belt Grabbers

Adjust the grabber belt length so the distance between the roller on the inner arm and the outside roller is 30” (+/- 1”).
See illustration below.

NOTICE

The grabber belt holes on the inside end of the belt are farther apart to make longer adjustments. The holes on the
outside end of the belt are closer together to make shorter adjustments.

NOTICE

When the grabbers are used with the Python Lift, adjust the outer rollers so that they do not touch each other when the
grabbers are completely closed.

Figure 16. 60-90 Gallon Belt Grabbers

«
...
54
55
56
57
58
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: Bang & Olufsen Страницы: 2

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: National Instruments Страницы: 22

Бренд: Aveo Engineering Страницы: 16

Бренд: Meritor Страницы: 65

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренд: Frick Страницы: 36

Бренд: Karma Страницы: 12

Бренд: Blackrock Microsystems Страницы: 74

Бренд: Kleinwaechter Страницы: 8

WELDPLAST 200-i

Бренд: Leister Страницы: 20

Бренд: HydroHoist Страницы: 19

Бренд: Master Страницы: 80

Бренд: Southwire Страницы: 15

Бренд: Rottler Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды