Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 23

Страница: 23 / 136

Issued May 2020

General Information

General Information

STANDARD TORQUE DATA FOR NUTS AND BOLTS

The following recommended torque data is for use as a general guideline. Recommended torque, in foot pounds, for all
Standard Application nuts and bolts provided in the following table.

NOTICE

Torque specifications on a drawing override torque values in the Standard Torque Data for Nuts and Bolts Table.

All thread surfaces are clean and lubricated with SAE-30 engine oil. See notice above.

Joints are rigid, that is no gaskets or compressible materials are used

When re-using nuts or bolts use minimum torque values

STANDARD TORQUE DATA FOR NUTS AND BOLTS TABLE

Bolt Size
(D)

Nut Type
(STD/Lock)

Thread
Turns per
Inch
(p)

Grade

Heil Plain Dry
Condition
Torque Value
(ft-lbs)

Heil Zinc
Plated
Fastener
Torque
Value
(ft-lbs)

Heil
Lubricated
Fastener
Torque Value
(ft-lbs)

Heil
Deformed
Lock Nut
Torque Value
(ft-lbs)

1/4

STD

0.25

Lock

5/16

STD

.3125

Lock

3/8

STD

.375

Lock

Содержание HEIL LIBERTY TP1L-SM-0520










































































































Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию

Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды