Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 100

Страница: 100 / 136

Issued May 2020
Body Controller Software

Printed in the U.S.A.

BODY CONTROLLER SOFTWARE

CONTROL AREA NETWORK (CAN)

The control system for the 2018 Liberty has multiple components that communicate via messaging over Control Area
Networks or CAN.

a. Body Controller (32 I/O Cortex Control Module)

b. Cab Controller (32 I/O Cortex Control Module)

c. Insight Display

d. Control panel Switch Bank(s)

e. Chassis J1939 interface.

There are three discrete networks in the system.

CAN1 Network

Communications between the Body Controller, Cab Controller and Insight Display.

DEV-J1939 Network

Communications between the Body Controller and switch banks or other devices that may be added.

CH-J1939 Network

Communications between the Cab Controller and the truck chassis J1939.

Baud Rates

The baud rate setting determines the speed at which messages are transmitted between devices. The baud rate setting
for all devices on the network must match.

a. CAN1 – 250K fixed

b. DEV-J1939 – 250K fixed

c. CH-J1939 –250K or 500K adjust to match chassis J1939 network.

Содержание HEIL LIBERTY TP1L-SM-0520










































































































Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию

Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды