Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 94

Страница: 94 / 363

Alphabetical list of commands

set debug-log-parameters

Description

Sets the types of debug messages to include in the Storage Controller debug log. For use by or with

direction from technical support.

Min. role

manage

Syntax

set debug-log-parameters

message-type

+|- [...]

Parameters

message-type

+|-

One of the following message types, followed by a plus (+) to enable or a minus (-) to disable

inclusion in the log:

•

awt

: Auto-write-through cache triggers debug messages. Disabled by default.

•

bkcfg

: Internal configuration debug messages. Enabled by default.

•

cache

: Cache debug messages. Enabled by default.

•

capi

: Internal Configuration API debug messages. Enabled by default.

•

capi2

: Internal Configuration API tracing debug messages. Disabled by default.

•

disk

: Disk interface debug messages. Enabled by default.

•

dms

: Not used

•

emp

: Enclosure Management Processor debug messages. Enabled by default.

•

: Failover and recovery debug messages. Enabled by default.

•

fruid

: FRU ID debug messages. Enabled by default.

•

: Not used.

•

host

: Host interface debug messages. Enabled by default.

•

init

: Not used.

•

ioa

: I/O interface driver debug messages (standard). Enabled by default.

•

iob

: I/O interface driver debug messages (resource counts). Disabled by default.

•

ioc

: I/O interface driver debug messages (upper layer, verbose). Disabled by default.

•

iod

: I/O interface driver debug messages (lower layer, verbose). Disabled by default.

•

mem

: Internal memory debug messages. Disabled by default.

•

misc

: Internal debug messages. Enabled by default.

•

msg

: Inter-controller message debug messages. Enabled by default.

•

mui

: Internal service interface debug messages. Enabled by default.

•

: Not used.

•

raid

: RAID debug messages. Enabled by default.

•

rcm

: Removable-component manager debug messages. Disabled by default.

•

res2

: Internal debug messages. Disabled by default.

•

resmgr

: Reservation Manager debug messages. Disabled by default.

Example

Include RAID and cache messages, exclude EMP messages, and leave other message types

unchanged.

# set debug-log-parameters raid+ cache+ emp-

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 94 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: