Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 289

Страница: 289 / 363

log-header-table 289

log-header-table

This basetype is used in the log file downloaded from the system by using the WBI or FTP.

Table 45

log-header-table properties

Name

Type

Description

log-contact

string

Contact person's name, if specified in the WBI Save Logs panel.

log-email

string

Contact's email address, if specified in the WBI Save Logs panel.

log-phone

string

Contact's phone number, if specified in the WBI Save Logs panel.

log-comments

string

Comments describing the problem and specifying the date and time when the

problem occurred, if specified in the WBI Save Logs panel.

log-content

uint32

For internal use only.

log-timestamp

string

Date and time, in the format

year-month-day hour

minutes

seconds

(UTC), when log content was saved to the file.

log-timestamp-

numeric

uint32

Unformatted

log-timestamp

value.

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 289 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: