Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 281

Страница: 281 / 363

hosts 281

hosts

This basetype is used by

show hosts (Deprecated)

Table 38

hosts properties

Name

Type

Description

host-id

string

SAS host port WWN.

host-name

string

User-defined name of the host port, or blank.

host-discovered

string

•

Yes

: The host was discovered and its entry was automatically created.

•

: The host entry was manually created.

host-mapped

string

•

Yes

: At least one volume is explicitly mapped to the host.

•

: No volumes are explicitly mapped to the host.

host-profile

string

•

Standard

: Default profile.

host-bus-type

string

•

If the host was discovered and its entry was automatically created, its host

interface type:

SAS

•

If the host entry was manually created:

Undefined

host-port-bits-

uint32

For internal use only.

host-port-bits-

uint32

For internal use only.

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 281 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: