Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 363

Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 28

28

Alphabetical list of commands

check firmware-upgrade-health

Description

Checks that the system is ready for a firmware upgrade.
Under normal conditions, firmware upgrade can be performed safely without risk to data availability

or integrity. However, when the system is degraded—for example, because of failed or missing

components or lack of multi-pathing to disks—upgrade failure or loss of availability can occur.
This command performs a series of health checks to determine whether any conditions exist that

need to be resolved before upgrading firmware. Any conditions that are detected are listed with their

potential risks. You can use commands in the “See also” section to determine which components

have health problems to be resolved.

Min. role

manage

Syntax

check firmware-upgrade-health

Output

Upgrade Health

•

Pass

: There are no risks to performing firmware upgrade.

•

Fail

: At least one condition exists that presents a risk of upgrade failure or loss of availability.

Condition Detected

The condition that was detected.

Risks

The problems that are likely to result if you do not resolve the conditions before performing a

firmware upgrade.

Example

Check firmware upgrade health for a system that is ready for upgrade.

# check firmware-upgrade-health

Upgrade Health

---------------------------------

Pass

---------------------------------

Success: Command completed successfully. (2014-06-07 15:14:33)

«
...
26
27
28
29
30
...
»

Содержание AssuredSAN 6004












































































































































































































































































































































































Отзывы:

Нет отзывов