Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 211

Страница: 211 / 363

shutdown 211

shutdown

Description

Shuts down the Storage Controller in a controller module. This ensures that a proper failover

sequence is used, which includes stopping all I/O operations and writing any data in write cache to

disk. If the Storage Controller in each controller module is shut down, hosts cannot access the

system’s data. Perform a shut down before removing a controller module or powering down the

system.

Min. role

manage

Syntax

shutdown

[a|b|both]

Parameters

a|b|both

Optional. Specifies to shut down the Storage Controller in controller A, B, or both. If this parameter

is omitted, the command affects the controller being accessed.

Example

Shut down the Storage Controller in controller A.

# shutdown a

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 211 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: