Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 204

Страница: 204 / 363

204 Alphabetical list of commands

show versions

show volume-maps (Deprecated)

Use

show maps

Description

Shows firmware and hardware version information for each controller module.

Min. role

monitor

Syntax

show versions

[detail]

Parameters

detail

Optional. Shows information about the versions of firmware and hardware in each controller

module. If this parameter is omitted, only firmware-bundle information is shown.

Example

Show firmware-bundle version information for the system.

# show versions

Show detailed version information for each controller module.

# show versions detail

Basetypes •

versions

•

status

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 204 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: