Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 194

Страница: 194 / 363

194 Alphabetical list of commands

show unwritable-cache

Description

Shows the percentage of unwritable data in the system. This data has not been written to disk

because it is associated with a volume that no longer exists or whose disks are not online. If the data

is needed, the volume’s disks must be brought online. If the data is not needed it can be cleared, in

which case it will be lost and data will differ between the host and disk.

Min. role

monitor

Syntax

show unwritable-cache

Output

Percent of unwritable cache in controller ID

The percentage of cache space occupied by unwritable data in the indicated controller module.

Example

Show the percentage of unwritable cache data in each controller.

# show unwritable-cache

Basetypes •

unwritable-cache

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 194 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: