manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 174 / 363

Поделиться
Скачать
Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 174

174 Alphabetical list of commands

show ports

Description

Shows information about host ports in both controllers.

Min. role

monitor

Syntax

show ports

[detail]

Parameters

detail

Optional. This parameter shows additional detail about the port status.

Output

Ports

Controller ID and port number

Media

•

SAS

: Serial Attached SCSI

Target ID

Port WWN

Status

•

Up

: The port is cabled and has an I/O link.

•

Warning

: Not all of the port’s PHYs are up.

•

Error

: The port is reporting an error condition.

•

Not Present

: The controller module is not installed or is down.

•

Disconnected

: Either no I/O link is detected or the port is not cabled.

Speed(A)

•

Actual link speed in Gbit/s.

•

Blank if not applicable.

Speed(C)

Configured host-port link speed. Not shown for SAS.

•

Blank if not applicable

Health

•

OK

•

Degraded

•

Fault

•

N/A

•

Unknown

Reason

If Health is not 

OK

, this field shows the reason for the health state.

Action

If Health is not 

OK

, this field shows recommended actions to take to resolve the health issue.

Topo (C)

SAS only. Configured topology.

Lanes Expected

SAS only. If the 

detail

 parameter is specified, this field shows the expected number of PHY lanes in 

the SAS port.

Active Lanes

SAS only. If the 

detail

 parameter is specified, this field shows the number of active lanes in the 

SAS port. If the port is connected and fewer lanes are active than are expected, the port status will 

change to 

Warning

, the health will change to 

Degraded

, and event 354 will be logged.

Содержание AssuredSAN 6004












































































































































































































































































































































































Отзывы:

Нет отзывов