Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 168

Страница: 168 / 363

168 Alphabetical list of commands

show initiators

Description

Shows information about initiators. The command will show information about all initiators by

default, or you can use parameters to filter the output.
Initiator entries are automatically created for host initiators that have sent an

inquiry

command or

report luns

command to the system. This typically happens when the physical host containing

an initiator boots up or scans for devices. When the command is received, the system saves the host

port information. However, the information is retained after a restart only if you have set a name for

the initiator.

Syntax

show initiators

[

initiators

]

Parameters

initiators

Optional. A comma-separated list of the names of initiators for which to show information. If this

parameter is omitted, information is shown for all initiators.

Output

Nickname

The name of the initiator.

Discovered

•

Yes

: The initiator was discovered and its entry was automatically created.

•

: The initiator was manually created.

Mapped

Shows whether the initiator is explicitly mapped to any volumes:

•

Yes

: At least one volume is explicitly mapped to the initiator.

•

: No volumes are explicitly mapped to the initiator.

Host Type

The host-interface type.

•

For a SAS initiator, its WWPN.

Example

Show information about all initiators.

# show initiators

Basetypes •

initiator

•

status

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 168 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: