Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 148

Страница: 148 / 363

148 Alphabetical list of commands

Status

Shown by the

encl

parameter.

•

: The disk is present and is properly communicating with the expander.

•

Spun Down

: The disk is present and has been spun down by the drive spin down feature.

•

Warning

: The disk is present but the system is having communication problems with the disk LED

processor. For disk and midplane types where this processor also controls power to the disk,

power-on failure will result in

Error

status.

•

Error

: The disk is present but is not detected by the expander.

•

Unknown

: Initial status when the disk is first detected or powered on.

•

Not Present

: The disk slot indicates that no disk is present.

•

Unrecoverable

: The disk is present but has unrecoverable errors.

•

Unavailable

: The disk is present but cannot communicate with the expander.

•

Unsupported

: The disk is present but is an unsupported type.

Temperature

Shown by the

detail

temp

parameter. The temperature of the disk.

Temperature Status

Shown by the

temp

parameter.

•

: The disk sensor is present and detects no error condition.

•

Warning

: The disk sensor detected a non-critical error condition. The temperature is between the

warning and critical thresholds.

•

Critical

: The disk sensor detected a critical error condition. The temperature currently exceeds

the critical threshold.

•

Unknown

: The disk sensor is present but status is not available.

Total I/Os

Shown by the

perf

parameter. The total number of I/O operations (reads and writes).

Transfer Rate

Shown by the

detail

parameter. The data transfer rate in Gbit/s. A footnote indicates that it is

normal behavior for the rate to vary.
Some 6-Gbit/s disks might not consistently support a 6-Gbit/s transfer rate. If this happens, the

controller automatically adjusts transfers to those disks to 3 Gbit/s, increasing reliability and

reducing error messages with little impact on system performance. This rate adjustment persists until

the controller is restarted or power-cycled.

Usage

Shown by default or by the

detail

parameter

•

AVAIL

: Available

•

FAILED

: The disk is unusable and must be replaced. Reasons for this status include: excessive

media errors, SMART error, disk hardware failure, or unsupported disk.

•

GLOBAL SP

: The disk is a global spare.

•

LEFTOVR

: The disk is a leftover.

•

VDISK

: The disk is a member of a vdisk.

•

VDISK SP

: The disk is a spare assigned to a vdisk.

Vdisk

Shown by default or by the

detail

parameter. The name of the vdisk that contains the disk.

Vendor

Shown by default and by any parameter except

temp

. The vendor of the disk.

Example

Show disk information.

# show disks

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 148 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: