Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 134

Страница: 134 / 363

134 Alphabetical list of commands

show controller-date

Description

Shows the system’s current date and time.

Min. role

monitor

Syntax

show controller-date

Output

Controller Date

Date and time in the format

year-month-day hour

minutes

seconds.

Time-Zone Offset

The system’s time zone as an offset in hours and minutes from Coordinated Universal Time (UTC).

This is shown only if NTP is enabled.

Example

Show the system date and time.

# show controller-date

Basetypes •

time-settings-table

•

status

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 134 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: