Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 126

Страница: 126 / 363

126 Alphabetical list of commands

Fan Failure

Shows whether the cache policy will change from write-back to write-through when a fan fails.

•

Disabled

: The fan failure trigger is disabled. This is the default.

•

Enabled

: The fan failure trigger is enabled.

Temperature Exceeded

Shows whether the system will shut down a controller when its temperature exceeds the critical

operating range.

•

Disabled

: The over-temperature failure trigger is disabled. This is the default.

•

Enabled

: The over-temperature failure trigger is enabled.

Partner Notify

Shows whether the partner controller will be notified when a trigger condition occurs.

•

Disabled

: Notification is disabled. The partner controller will continue using its current caching

mode. This is the default.

•

Enabled

: Notification is enabled. The partner controller will change to write-through mode for

better data protection.

Auto Write Back

Shows whether the cache mode will change from write-through to write-back when the trigger

condition is cleared.

•

Disabled

: Auto-write-back is disabled.

•

Enabled

: Auto-write-back is enabled. This is the default.

Inactive Drive Spin Down

Shows whether available disks and global spares will spin down after a period of inactivity shown

by the

Inactive Drive Spin Down Delay

field.

•

Disabled

: Drive spin down for available disks and global spares is disabled. This is the default.

•

Enabled

: Drive spin down for available disks and global spares is enabled.

Inactive Drive Spin Down Delay

Shows the period of inactivity in minutes after which available disks and global spares will spin

down, from 1 to 360 minutes. The value 0 means spin down is disabled. The default is 15 minutes.

Disk Background Scrub

Shows whether disks that are not in vdisks are automatically checked for disk defects to ensure

system health. The interval between background disk scrub finishing and starting again is 72 hours.

•

Disabled

: Background disk scrub is disabled. This is the default.

•

Enabled

: Background disk scrub is enabled.

Managed Logs

Shows whether the managed logs feature is enabled, which allows log files to be transferred from

the storage system to a log collection system to avoid losing diagnostic data as logs fill.

•

Disabled

: The managed logs feature is disabled. This is the default.

•

Enabled

: The managed logs feature is enabled.

Single Controller Mode

For a 2U12 or 2U24 system that had two controller modules but now has only one and is intended

to be used as a single-controller system, this property shows whether the operating/redundancy

mode is set to Single Controller. This prevents the system from reporting the absent partner controller

as an error condition. This parameter does not affect any other system settings. Installing a second,

functional controller module will change the mode to Active-Active ULP.

•

Enabled

: Single Controller mode is enabled.

•

Disabled

: Single Controller mode is disabled.

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 126 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: