please use home freezer
MAX
How to use 1
Parts Name
How to use 2
Preparation
Thoroughly wash all parts other
than the insulated container,
wipe off any water droplets and
dry thoroughly.
1.
※
To remove dirt from the insulated container,
wring out a wet cloth and gently wipe the surface.
Slowly place the combined
ice molds into the water
reservoir.
4.
※Water may spill when the combined ice
molds are placed into the water reservoir.
Freeze the ice-making unit in
the freezer for at least 20 hours.
7.
※
The ice-making time varies depending on the season,
ambient conditions, frequency of freezer access,
freezer model and the storage capacity.
Pour water up to the MAX line
of the water reservoir.
2.
Caution
Caution
Preparation
Use a freezer with a JIS rating of at least three stars (
Set the temperature dial of the freezer to "Strong" (-18 °C or cooler).
).
・
Air vent holes
freezer
Before use
Before using for the first time, check that there are no defects such
as scratches, dents, or cracks.
Do not remove the sticker on the water reservoir.
Before using for the first time, wash all parts other than the insulated
container with a sponge soaked in dishwashing detergent.
Insulated containers may lose color when detergent is applied.
In the event of a defect, discontinue use and contact your retailer or
our customer service office.
•
•
•
•
Air vent holes
Extraction tabs
MAX line
DCI-20DM
DCI-20DM
DCI-20HT
DCI-20DM
DCI-20HT
DCI-20HT
Ice molds
Water reservoir
Insulated container
3
4
2
Continued on the reverse side
← 110 ｍｍ →
← 110 ｍｍ →
← 109 ｍｍ →
Ice-
making
unit
Ice-
making
unit
Pour water in an area that is not prone to
water damage.
If the water is not filled to the MAX line,
the ice may not be a perfect shape.
Do not fill with any liquid other than water.
•
•
•
Water may spray out of the air vents if
the molds are moved too forcefully.
Push them down until they are firmly
in place.
Water will spill from the water reservoir.
As it does so, the corners of the ice
molds will fill with water to ensure that
a complete 3D shape is formed.
Before performing this step, place the
molds on a tray to collect any water that
spills from the water reservoir.
•
•
Combine the 2 ice molds.
3.
Caution
Ensure that the molds are securely
attached to one another.
•
Wipe the outside of the water
reservoir before placing it into
the insulated container.
5.
Caution
Place the water reservoir on a flat surface.
Wipe the outside of the wet water reservoir
thoroughly before placing it into the insulated
container. Push it down until it is firmly in place.
•
•
Place the ice-making unit in
the freezer. Place it slowly so
that water does not spill.
6.
Caution
Place on a flat surface. Failure to do so
may cause water to spill.
If the insulated container is wet, wipe it
with a dry cloth before placing it in the
freezer, otherwise it may stick to the freezer
and cause damage.
Do not place any items on this product,
otherwise it may become deformed.
Carry the ice-making unit by the insulated
container, otherwise the insulated
container may fall to the ground.
•
Do not use a two-star (
) freezer.
•
Even if it’s a three-star freezer (
approximately 10 years of use. If you are using an older freezer, extend the freezing
time accordingly.
Do not place the ice-making unit near the freezer entrance. Open and close the freezer
as infrequently as possible, otherwise warm air may flow in and the freezer will not freeze
properly.
Do not place the product next to food which is still warm, as this may prevent the ice from
forming.
) freezer performance drops significantly after
•
•
•
•
•
•