Battery indicator and charging
The symbol
|
in the display indicates when
the batteries require charging. The indicator has
three segments which disappear as the battery
charge decreases, and will flash when the battery
is running low. Charge the equipment as soon as
possible when the indicator flashes!
The battery indicator will show
|
when
charging is complete (approximately 10 hours/
initially 24 hours). Fully-charged batteries will last
for approximately 35 hours in standby or 2 hours
operational time. These times apply at normal
room temperature.
Please note!
Never charge ordinary (non-rechargeable) batteries in the
handset, since this will ruin the equipment. The guarantee
does not cover this type of damage. The equipment must be
charged initially for 24 hours before use during which time
the handset cannot be used. The recharging system used in
this model may result in it becoming warm. This is normal
and will not damage the equipment.
Important!
Please note when programming all references to press = to
press and then immediately release the button.
Switching the Handset on/off
Press and hold
1
for a few seconds to turn the
handset on or off.
To communicate
1.
Make sure that all handsets (and monitor unit)
are set to the same channel and transfer code.
See below.
2.
Press and hold
PTT
(Push To Talk) to speak.
Please note!
If you are unable to communicate it may be because different
channels or transfer codes have been selected, the battery is
running low or the units are too far apart.
Channel selection
All UHF/CB radio equipment share the available
designated channels. If the chosen channel is in use
select an alternate channel, the selected channel
number will be displayed in standby mode.
1.
Press
w
. The current selected channel flashes.
2.
Select the desired channel using
v
/
V
.
3.
Press
PTT
.
Monitor function
The monitor function can be used in weak signal
areas to locate any other signal being transmitted.
1.
Press
w
and
V
at the same time.
2.
To stop monitoring press
w
.
Transfer code selection
There are 38 transfer codes available which can be
used to filter out unwanted signals. However, your
conversation may still be overheard irrespective
of which code is used. To enable communication
between handsets (as well as monitor to handset), the
same transfer code must be used on all units. In order
to communicate with equipment that cannot select a
code, enter code 0.
1.
Press
w
repeatedly until the small digits in the
top right hand corner of the display flash.
2.
Scroll to the desired transfer code using
v
/
V
.
3.
Press
PTT
to confirm.
Scanning
You can scan all available channels to locate any
signals being transmitted. Once a signal has been
located the display will show the channel number,
and a signal will be heard for a few seconds.
You can press
PTT
to stop at the located channel.
Please note: while searching battery consumption will
be significantly higher than normal.
1.
Press
w
and
{
at the same time. The unit will
start searching.
2.
To stop scanning press
w
.
Voice control (VOX)
This handset can be used without having to press the
PTT
button to transmit. By setting the correct level,
the handset can automatically determine when you
are speaking.
Test different settings until the sensitivity selected is
acceptable. Please note that however accurate your
setting there is always a small risk that increased noise
from the surroundings may activate the transmitter,
this may result in the initial word being unclear. The
transmitter will shut off two seconds after you have
finished speaking.
VOX
will be displayed while the function is active. If
the handset transmits by itself the sensitivity is set too
high and will need to be adjusted. Press
w
to be able
to temporarily interrupt and change the setting.
1.
Press
w
repeatedly until
VOX
is displayed.
2.
Scroll to the desired setting using
v
/
V
(
OF
=off, 1=least sensitive....3=most sensitive).
3.
Press
PTT
to confirm.
Call melody
You can select different call melodies (
OF
=off).
1.
Press
w
repeatedly until
CA
is displayed.
2.
Scroll to the desired melody (1 -5) using
v
/
V
.
3.
Press
PTT
to confirm.
1 Headset socket
2 Push to Talk (PTT)
button
3 Call button
4 DOWN
5 Menu button
6 UP
7 On/Off button
Area of use
The handset is intended for both indoor and
outdoor use, it is NOT resistant to rain, water,
rough or other careless treatment.
In ideal conditions ie: line of sight with no
obstructions between handset/s and monitor, the
range can be up to 6 km.
Batteries
1.
Remove the belt clip by lifting the small
locating tab and pushing the clip upwards.
2.
Before removing the battery cover release the
locking clasp at the base of the handset.
3.
Insert the rechargeable battery pack ensuring
correct battery polarity is observed.
4.
Refit the battery cover and belt clip. Charge the
handset for 24 hours before use.
Please note!
The rechargeable battery pack has been installed the handset
must be charged for 24 hours before use.
Charging
Connect the mains adapter to the socket on the
rear of the charging stand and to an electrical wall
socket. Place the handset in the charger with the
buttons facing out.
English
Termination (Roger) tone
If selected a beep tone will be heard when you
release the
PTT
button. This can be used as a
reminder to the other person that you have finished
talking and are waiting for a response.
1.
Press
w
repeatedly until
ro
is displayed.
2.
Scroll to the desired setting using
v
/
V
(
OF
=off,
On
=on).
3.
Press
PTT
to confirm.
Key tone
If selected a tone will be heard when the handset
buttons are pressed, this can be switched on or off.
1.
Press
w
repeatedly until
to
is displayed.
2.
Scroll to the desired setting using
v
/
V
(
OF
=off,
On
=on).
3.
Press
PTT
to confirm.
Searching two channels
You can enter a different channel for simultaneous
listening while using the selected operating channel.
1.
Press
w
repeatedly until
DCM
is displayed.
2.
Scroll to the desired setting using
v
/
V
(
OF
=off). Press
w
.
3.
Scroll to the desired transfer code using
v
/
V
.
Press
PTT
.
4.
Press
PTT
to confirm.
Key lock
This function locks buttons
w
and
v
/
V
to
prevent unintentional usage.
1.
To activate the key lock press
w
until the display
shows the key symbol.
2.
To deactivate the key lock press and hold
w
until the key symbol disappears.
Declaration of conformity
Doro declares that the apparatus Doro wt86
complies with the essential requirements and other
relevant positions of Directive 1999/5/EC. A copy
of the Declaration of Conformity can be found at
www.doro.com/dofc
Guarantee
This product is guaranteed for a period of 12 months from
the date of purchase. Proof of purchase is required for any
service or support required during the guarantee period. This
guarantee shall not apply to a fault caused by an accident
or a similar incident or damage, liquid ingress, negligence,
abnormal usage, not reasonably maintained or any other
circumstances on the purchaser’s part. Furthermore, this
guarantee shall not apply to a faults caused by the use of poor
quality batteries, battery leakage, corrosion or similar events
related to non DORO batteries. This guarantee does not in
any way affect your statutory rights.
1
2
3
4
5
7
6