manualshive.com logo in svg

Dorner iDrive 3200 Series, Инструкция по установке, эксплуатации и ремонту

Поделиться
Скачать
Dorner iDrive 3200 Series Скачать руководство пользователя страница 11

851-702 Rev. A

11

Dorner Mfg. Corp.

3200 Series iDrive Belt Conveyors

Installation

Potentiometers

Jumpers

NOTE:

 Refer to Dart Controls Instruction Manual for 700B Control Series for further details.

Change Acceleration / Deceleration 
Settings

1. Remove belt. (See “Belt Removal for Conveyor Without 

Stands” on page 13 or “Belt Removal for Conveyor 
With Stands” on page 13.)

2. Remove control board mounting screws 

(Figure 

22, item 1)

 from bottom of plate.

 Figure 22

 Figure 22           

3. Locate potentiometers to change. See Controller Board 

layout on page 10.

4. Rotate potentiometers 

(Figure 23, item 1) 

to desired 

setting.

 Figure 23

 Figure 23           

5. Reinstall by reversing steps.

Item Number

Description

Setting

1

Current Limit %

100%

2

Gain %

N/A

3

Max. Speed %

100%

4

Min. Speed %

5%

5

Decel. (0-10 sec.)

0 sec.

6

Accel. (0-10 sec.)

0.5 sec.

Item Number

Description

Position

Setting

7

Input Voltage (P3)

P3-2 & 3 (36)

24/36 VDC

8

Sensor Spacing (P2)

P2-1 & 2 (120)

120 deg.

9

Potentiometer Function (P5)

P5-2 & 3 (U)

Unidirectional

A

 WARNING

Exposed moving parts can cause severe 
injury. LOCK OUT POWER before removing 
guards or performing maintenance.

1

1

Содержание iDrive 3200 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды