Dorner 62M005ESBDDEN Скачать руководство пользователя

Страница: 3 / 20

851-738 Rev. A

Dorner Mfg. Corp.

Brushless DC Motor Control

Warnings

General Safety

WARNING

The safety alert symbol, black triangle with
white exclamation, is used to alert you to
potential personal injury hazards.

DANGER

SEVERE HAZARD!

KEEP OFF CONVEYORS. Climbing, sitting,
walking or riding on conveyor will cause
severe injury.

DANGER

EXPLOSION HAZARD!

• DO NOT OPERATE CONVEYORS IN AN

EXPLOSIVE ENVIRONMENT. The electric
gearmotor generates heat and could ignite
combustible vapors.

• Failure to comply will result in death or

serious injury.

WARNING

Controller must be properly grounded.
Failure to properly ground controller may
cause injury to personnel.

DANGER

SEVERE HAZARD!

Hazardous voltage will cause severe injury
or death. LOCKOUT POWER BEFORE
WIRING.

WARNING

SEVERE HAZARD!

Exposed moving parts can cause severe
injury. DO NOT ATTEMPT ADJUSTMENTS
WITH CONVEYOR RUNNING. LOCK OUT
POWER before removing guards or
performing maintenance.

WARNING

SEVERE HAZARD!

• Dorner cannot control the physical

installation and application of conveyors.
Taking protective measures is the
responsibility of the user.

• When conveyors are used in conjunction

with other equipment or as part of a
multiple conveyor system, CHECK FOR
POTENTIAL PINCH POINTS and other
mechanical hazards before system start-
up.

• Failure to comply could result in serious

injury.

Содержание 62M005ESBDDEN





















Результаты поиска

Содержание 62M005ESBDDEN

Отзывы:

Похожие инструкции для 62M005ESBDDEN

Бренды по названию

Популярные бренды

Dorner 62M005ESBDDEN, Инструкция по установке, эксплуатации и запасным частям

Результаты поиска

Содержание 62M005ESBDDEN

Отзывы:

Похожие инструкции для 62M005ESBDDEN

Бренды по названию

Популярные бренды