Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 196

background image

Engine Operation

Engine Operation and Maintenance

We, Doosan Infracore, do our best to provide more convenient and safe maintenance
techniques and to meet the requirements of our customers. If you have any questions or find
any errors in this Operation and Maintenance Manual, please do not hesitate to contact us.

Thank you for purchasing our engine and we hope this Operation and Maintenance Section
will be helpful for you.

General Information

This Operation and Maintenance Section provides the most efficient methods for engine
maintenance as well as quick, efficient methods to determine the cause of engine faults to
ensure that any actions taken by professionally certified maintenance technicians are done
in the most efficient way possible. If maintenance is performed by unskilled technicians, or
maintenance performed without the specified tools and facilities, serious bodily injury or
critical faults in engine performance may occur.

Regular inspection and maintenance are required to maintain long term optimal engine
conditions and best performance. In the event that a part must be replaced, only genuine
Doosan parts, as defined by the parts list (Parts Manual) should be used. Doosan shall
not be held liable for any critical damage or faults which may be caused by the use of
unauthorized or non-factory remanufactured parts.

The maintenance methods stated in this Operation and Maintenance Section are the most
efficient and safest work procedures. Some work procedures require special tools.

For questions about genuine parts and special tools, please contact us.

This Operation and Maintenance Section includes

Danger, Warning, and Caution

headings

in order to reduce possible injuries and engine faults which may occur while performing
maintenance. If workers do not follow the instructions, critical faults in engine performance
and operation or serious bodily injury may occur.

Danger, Warning, and Caution

instructions

must be followed.

Engine Management

If the radiator cap is opened while the engine is still hot, hot water will
spurt out and may cause burns.

Using inappropriate or unspecified fuel may cause critical damage,
faults, and diminished engine performance.

78

«
...
76
77
78
79
80
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: Campbell Страницы: 68

Бренд: ULTIMATE SPEED Страницы: 122

Бренд: Daewoo Страницы: 20

ELECTRA-SAVER II

Бренд: Gardner Denver Страницы: 62

Бренд: Craftsman Страницы: 52

Бренд: DeWalt Страницы: 29

Бренд: DeWalt Страницы: 100

Бренд: DeWalt Страницы: 72

Бренд: DeWalt Страницы: 92

Бренд: Carrier Страницы: 20

Бренд: Carrier Страницы: 40

Бренд: Crown Страницы: 72

Бренд: Crown Страницы: 140

Бренд: XTM Страницы: 2

Бренд: Atlas Copco Страницы: 64

Бренд: Atlas Copco Страницы: 76

Бренд: Atlas Copco Страницы: 94

Бренд: Proxxon Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды