manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 73

Operating Instructions

Normal Operation

The operator may observe and monitor operating parameters using the Mini-Port and
gauges. In the event the compressor controller detects a parameter outside normal operating
limits, the compressor will alert and/or shutdown, and display a diagnostic code.

In the event the compressor controller detects a parameter at a dangerously high or low level,
the compressor will be automatically shut down with the cause of the shutdown shown on
the Mini-Port.

Operation-Loaded

Assume engine has been started and is running in the unload state at idle speed. If there is air
demand (pressure falls below the load point pressure), compressor will load at idle speed by
opening the inlet valve. As air demand rises and falls, engine speed is controlled between idle
speed and full load speed to match the required flow while maintaining load point pressure.

Operation-Unloaded

If there is no air demand at idle speed (pressure rises above the unload point pressure), the
compressor will unload by closing the inlet valve. The compressor then runs at idle speed
unloaded with no air delivery. If air demand increases (pressure falls below the load point
pressure), the compressor reloads to meet the required air demand.

73

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды