manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 56

General Data

HP Available for Auxiliary Power Use

XP185WDOUA-T4F Model

NOTE

The XP185WDOU model is designed to have excess power available to allow power to be
drawn from the engine to drive auxiliary equipment the customer may desire to use. The
application of this power is the responsibility of the customer. The following guidelines are
furnished to assist in that application.

1. An Auxiliary Drive (such as a hydraulic pump) can be mounted to the auxiliary drive

location on the right-hand side of the front of the engine.

2. The maximum auxiliary drive power from the engine auxiliary drive location is 15

HP at any engine speed.

3. Engine speed will vary depending on the air demand on the compressor. The more

air demand, the faster the engine will run.

4. Depending on hydraulic pump type selected, the pump flow could vary with engine

speed. It is recommended that the maximum flow rate of the pump be selected based
on the rated speed (2600 RPM) of the engine.

56

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды