Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 196

background image

Materials

Avoid inhalation of material substances.

The following substances may be produced during the operation of this compressor:

• Brake Lining Dust

• Engine Exhaust Fumes

Ensure that adequate ventilation of the cooling system and exhaust gases is maintained at
all times.

The following substances are used in the manufacture of this compressor and may be
hazardous to health if used incorrectly:

• Antifreeze

• compressor Oil

• Engine Oil

• Preservative Grease, Lubricating Grease

• Rust Preventative

• Diesel Fuel

• Battery Electrolyte

Avoid ingestion, skin contact, and inhalation of fumes.

Should compressor oil come into contact with the eyes, irrigate with water for at least 5
minutes.

Should compressor oil come into contact with the skin, wash off immediately. Consult a
physician if large amounts of compressor oil are ingested or if compressor oil is inhaled.
Never give fluids or induce vomiting if the patient is unconscious or having convulsions.

Safety data sheets for compressor and engine oils should be obtained from the oil supplier.

Do not start or operate this compressor in a confined area. Avoid breathing exhaust fumes
when working on or near the compressor.

This compressor may include such materials as oil, diesel fuel, antifreeze, brake fluid, oil/air
filters, and batteries which may require proper disposal when performing maintenance or
service tasks. Contact local authorities for proper disposal of these materials.

27

«
...
25
26
27
28
29
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: Campbell Hausfeld Страницы: 24

Бренд: GEA Страницы: 40

Бренд: Ribimex Страницы: 31

Бренд: ZIPPER MASCHINEN Страницы: 45

Бренд: Grizzly Страницы: 2

Бренд: Spokey Страницы: 32

LW 230 E II Compact

Бренд: L&W Compressors Страницы: 187

Бренд: FScurtis Страницы: 48

Бренд: GEA Страницы: 32

Бренд: ARB Страницы: 5

Бренд: ARB Страницы: 26

TE-AC 270/24/10

Бренд: EINHELL Страницы: 94

Бренд: EINHELL Страницы: 205

Бренд: Grip Rite Страницы: 40

Бренд: NORAUTO Страницы: 54

Delta 2 220/380V

Бренд: METZGER Technik Страницы: 12

Бренд: NATI Страницы: 22

Бренд: Badger Air-Brush Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды