Installation
Receiver Terminal Wiring
DoorKing Part Number
This receiver is
NOT
designed to be installed outdoors without being protected
from the weather. An outdoor enclosure is available for the receiver if required
(P/N 8057-110 - Metal Outdoor Box).
Install the 8059 receiver in a location so the antenna is
NOT surrounded by
metal and is in free air as high as possible above the ground.
A longer Coax
Antenna kit is available for the receiver if required (P/N 1514-073 - Includes
antenna, mounting “L” bracket and 15 feet of coax cable). An antenna amplifier
kit (P/N 8058-080) or a Yagi directional antenna kit (P/N 1514-072) is also
available for the receiver if required.
The
Programming LED
on the side of the case will blink as RF energy is
received. If the programming LED blinks or is on continuously, this
indicates that there may be interference on the frequency (318 MHz) and
short range may be the result. If this happens, try relocating the receiver
or remove the source of interference. An antenna amplifier or a
directional antenna may be needed.
Note:
Loop detectors and proximity
card readers can cause receiver interference.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
To Receiver Terminal #1 (Neg.)
To Receiver Terminal #2 (Pos.)
12-24 Volt
Transformer
DC Polarity Matters!
Removable
receiver terminal
for easy wiring.
Be sure the antenna, coax shield
and F connector are completely
isolated from the ground.
8059-080
80 Transmitter Codes
Stand-Alone Power and Device Wiring :
Connect 12 - 24 Volt AC or DC power to
terminals #1 and #2. Use minimum 18 AWG wire to power the receiver.
• If DC power is used (Transformer): Terminal #1 is
NEGATIVE
and Terminal #2 is
POSITIVE
.
• Connect the receiver relay contacts to the device to be activated.
- Receiver Terminal #3 is the relay contact
Normally OPEN
(N.O.)
- Receiver Terminal #4 is the relay contact Normally CLOSED (N.C.)
- Receiver Terminal #5 is the relay contact
Common
(C).
Wiegand Controller Wiring:
Receiver terminal #2 is
INPUT POWER
(12-24 V).
Receiver terminal #6 is Wiegand input power
COMMON
.
Receiver terminal #7 is Wiegand
DATA 0
.
Receiver terminal #8 is Wiegand
DATA 1
.
Use 22 AWG
shielded
wire, maximum
200 feet
, for Wiegand controller wiring.
Connect these terminals to the
corresponding terminals on
the Wiegand controller. Refer to the
DoorKing Wiegand controller installa-
tion manual 1835, 1837 or 1838 for
specific wiring information.
#1 - Input Power Common
(Negative)
#2 - Input Power
12-24 Volt AC, 12-24 Volt DC (Positive)
#3 - Relay Contact (Normally Open)
#4 - Relay Contact (Normally Closed)
#5 - Relay Contact (Common)
#6 - Wiegand Common
#7 - Wiegand Data 0
#8 - Wiegand Data 1
1 2
3 4
5 6
7 8
Programming LED
F Con
nector
Coax
Antenna
Kit
(Included)
18”
Coax
Cable
Terminals 3-4-5
rated for 30 volt,
1 amp max.
From “Low Voltage Common”
From “Radio Open”
From “Circuit Board” Power
Stand-Alone Gate Operator:
Connect the 3
wires from the gate operator as indicated. Refer
to the chosen gate operator’s installation/owner’s
manual for specific wiring information.
To Receiver Terminal #1
To Receiver Terminal #2
To Receiver Terminal #3
From “Low Voltage Common”
From “Data 1”
From “Data 0”
From “Circuit Board” Power
To Receiver Terminal #2
To Receiver Terminal #6
To Receiver Terminal #7
To Receiver Terminal #8
Recei
ver
Terminal
MODEL 8059 MicroCLIK
™
RF RECEIVER (WIEGAND)
The model 8059
RF Receiver
is designed for use as a Stand-Alone or Wiegand applications using Micro
CLIK
™ transmitters. Stand-Alone installa-
tions can store up to 80 transmitter codes in its memory. It is also programmed to recognize only certain Micro
CLIK
™ transmitter buttons when
using multiple button transmitters.
The 8059 receiver activates a built-in dry contact form “C” relay
when a programmed Micro
CLIK
™ transmitter code is received.
The received code
MUST
match the programmed
“Transmitter
Code”, “Facility Code”
(or not match the Facility Code if a
Wiegand controller is used)
,
and
“Transmitter Button Code”
before the receiver relay will activate.
Wiegand applications will output transmitter codes in 26-bit or 31-bit Wiegand format to an external Wiegand controller.
The Micro
CLIK
™ system is compatible with the HomeLink system found in many automobiles.
P/N 8066-080
P/N 8067-080
P/N 8068-080
1 Butt
on
2 Butto
n
3 Butt
on
Micro
CLIK
™ Transmitters
1837
