NC
NO
NO
RING
NC
C
ON
CLK
SEN
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
12
34
5
6
7
8
9
10
11
12
13
14
1
2
3
MIC
VOL
3 2 1
3 2 1
3
2
1
MASTER
CODE
16AC
16AC
BAT
1NO
1NC
1C
2RY
2C
A
Z
IMC
5VDC
IMD
SPKR
COM
MIC
PSW
CGND
PHONE
14
13
12
11
6
5
4
3
2
1
DOORKING
2363-010
PAIRED
ON
OFF
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
RF RANGE
CH
NET
ID
RCVD
ALLOW
DENY
STATUS
SYNC LOST
SYNC REVD
HEARTBEAT
DISPLAY
OFF/ON
RESET
RF
STAT STRENGTH
DOORKING
2361-010
WIRELESS BASEBOARD KIT
DoorKing Access Control System Board
Wireless
Baseboard
Wireless
Wireless
Baseboard
Baseboard
14-Pin Auxiliary
Terminal
Connection
Other Antenna Options
DoorKing Part Number
2361-080
This wireless baseboard kit provides wireless communication from the access control system to a wireless tracker expansion
board(s). Use this kit
ONLY
on DoorKing: 1833, 1835, 1837 and 1838 multi-door access controller access control systems.
The wireless baseboard
REPLACES
the 14-pin auxiliary terminal on the access control system’s board. The existing 16.5 VAC, 20 VA access control
system’s input power transformer is
REQUIRED
and is rewired to the 10-pin terminal #1-#2. Antenna is
REQUIRED
, see below for antenna options.
14)
13)
12)
11)
6)
5)
4)
3)
2)
1)
+12 VDC Power
Common
DATA 1
DATA 0
16 VAC Output
16 VAC Output
Back-up Battery-NEG
Back-up Battery-POS
16.5 VAC Input Power – 20 VA
16.5 VAC Input Power – 20 VA
Relay 2 (2C) Com
Relay 2 (2R
Y
)
Relay 1 (1C) Com
Relay 1 (1NO)
Optional -
Additional power for card readers
that use lighting for outdoor use.
REQUIRED
Power
Transformer
Optional -
maintains ONLY wiegand
operation during power outage.
10-Pin Terminal
Relay 1
Relay 2
18 AWG 100 ft max
16 AWG 200 ft max
Wire polarity
does not matter
Relay 2 Jumper
Set relay 2
jumper
for NO.
(Powers RS-232, elevator control, wiegand and wireless baseboard)
Wireless Repeater
Sold separately P/N 2364-080
The range is approximately
500 ft direct-line-of-sight with
no signal interference or
physical obstructions. May be
necessary to increase the
wireless communication range between the
access control system and the tracker
expansion board(s). See Repeater kit
instruction sheet for more information.
Cabinet Mounted
Dome Antenna
Included
(Vandal-resistant) The range is
approximately 100 ft direct-line-of-sight.
Install on top of the cabinet in the
existing antenna mounting hole (remove
plug).
Range is approximately
200 ft direct-line-of-sight.
Install on top of the cabinet.
NOT
vandal-resistant.
1833, 1835 and 1837 ONLY
Relay 0
Optional -
Wiegand 1 HARDWIRE input:
activates
Relay 1
for the access control
system’s programmed strike time.
Note:
NOT
available when using
wireless
tracker expansion board addresses 11-18.
10-Pin Terminal:
One 26-Bit wiegand access control device
(card reader) or up to 8 tracker expansion board addresses 11-18 (
NOT
wireless) may be
HARD
wired to the 10-pin terminal (#11-12-13-14) for
Gate/Door control if desired (
DO NOT
connect
HARDwired
tracker
expansion boards or card reader to wiegand 1 (terminals 11-14) if
WIRELESS
boards will be using wiegand 1). The wiegand 1 input will
activate whatever is wired to the access control system’s Relay 1 for the
access control system’s programmed strike time.
4-Pin Terminal:
Must
connect to access control
system’s
Relay 2
for
wireless
tracker expansion board
addresses
3-10
.
Must
connect to access control
system’s
Relay 1
for
wireless
tracker expansion board
addresses
11-18
.
Cabinet Mounted
Longer Range
Fixed Antenna Kit
Sold separately
Kit P/N: 1514-008
Externally Mounted
Longer Range
Adjustable
Antenna
Included
16.5 V
A
C
20 V
A
Note:
Terminals
can be removed
from board for
easy wiring.
4-Pin Terminal
Main Terminal
13 ft of cable
Range is approximately 500 ft
direct-line-of-sight. Install antenna
vertically as high as possible in free
air above access control system.
Important Antenna Note:
Antenna range
WILL
VARY GREATLY
depending on individual setup
(Antenna height above the ground, background
signal interference, physical obstructions
(trees, buildings etc.) and what antenna
you choose). Adverse weather (rain)
CAN
also affect antenna range.
Range testing is HIGHLY recommended
before FINAL installation.
Installation
Main
Door/Gate
Wireless T
racker Board Addresses 3-10
Wireless T
racker Board Addresses 11-18
