DoorHan DRIVE SHAFT-50PRO Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 18

DoorHan DRIVE SHAFT-50PRO Скачать руководство пользователя страница 5

5

DRIVE DEVICE

3. DRIVE DEVICE

1.  Release cord
2.  Hand chain
3.  Motor
4.  Control unit
5.  Transfer case
6.  Terminal switches of

encoder

7. Hand drive assembly
8. Control device

4. DRIVE INSTALLATION

1

2

3

4

5

6

7

8

4.1. Tools

ATTENTION!

Make sure that the gate is in good working order and the balancing mechanism counterbalances a gate leaf

before installation.
It is necessary to install the drive according to the instructions provided further (section 4.2 or 4.3).

4.2. Installation on the shaft

•  Install the first lock ring on a shaft of the gate.
•  Install the drive on a shaft of the gate (make sure that the drive key is in correct position) and fasten it to the mounting base.
•  Install the second lock ring on a shaft of the gate and push it closely to the drive.
•  Install the first lock ring closely to the drive and fix both lock rings.

1.

Wrench set

2.

Flat blade and cross screwdrivers set

3.

Metal drills set

4.

Masonry drills set

5.

Pliers

6.

Hack saw

7.

Electric drill

8.

Tape ruler (folding rule)

Closing ring

Bushing key

Operator

Closing ring

Bolt (M10)

Mounting bolt

Fastening bracket

Shaft

«
...
3
4
5
6
7
...
»

Содержание DRIVE SHAFT-50PRO



















Отзывы:

Нет отзывов