1 2
ASSEMBLY INSTRUCTIONS
1. Before you start to assemble your tree, place the tree stand on a level surface.
2. Assemble tree stand according to the assembly instruction for the tree stand.
3. Carefully insert bottom section (C) of tree into the assembled tree stand and tighten the screw. (See Fig.1)
4.
Insert the middle section (B) of the tree into the bottom section (C).
If the lights don’t light up, rotate the middle
section (B) on right or left direction until it falls into place, then insert vertically and tightly into the bottom section (C)
to ensure
proper circuit connection. (See Fig. 2)
5. Insert top section (A) into the middle section (B).
If the lights don’t light up, rotate the top section (A) on right or
left direction until it falls into place, then insert vertically and tightly into the middle section (B) to ensure
proper
circuit connection. (See Fig. 3)
6. Connect the end connector of power cord (D) with the connector fixed on the bottom section (C)in
correct direction (always match the protuberance on the end connector of power cord to the
protuberance on the connector fixed on the bottom section (C) according to the magnified drawing.
(See Fig. 4).
7. Open all the branches. (See Fig. 5)
8. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be
sure that all wires are free of branch hinges. (See Fig. 5)
9. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left
and one at the center of the main stem. Repeat pattern for each branch. (See Fig. 6)
10. Connect the plug of the power cord (D) from bottom section (C) to the wall outlet. Now your tree
should be completed with all lights illuminated. Your tree is ready to be decorated and enjoyed.
ASSEMBLY INSTRUCTIONS FOR TREE STAND
Fig.1
1. Tree stand consists of a
metal stand and a single
eye bolt. (See Fig.1)
Fig. 2
2. Open the stand to a 90 degree
angle until the hole lines up with
the hole on the tube. (See Fig.2)
Fig. 3
3. Insert an eye bolt and
screw into the hole. (See
Fig.3)
Fig. 4
4. Insert the tree into the stand and
adjust accordingly. The tree
should be straight and balanced
correctly. (See Fig.4)
IMPORTANT SAFETY INSTRUCTIONS
a)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
b)
Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c)
This seasonal use product is not intended for permanent installation or use.
d)
Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
e)
Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f)
Do not let lamps rest on the supply cord or on any wire.
g)
Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h)
This is an electric product – not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i)
Do not use this product for other than its intended use.
j)
Do not hang ornaments or other objects from cord, wire, or light string.
k)
Do not cover the product with cloth, paper or any material not part of the product when in use.
l)
This product contains an extension cord with a polarized plug (one prong is wider than the other) as a
feature to reduce the risk of electrical shock. This plug will fit in a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not use with an extension cord unless the plug can be fully inserted. Do not alter or
replace the plug.
m)
This product is equipped with push-in type lamps. Do not twist lamps.
n)
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the replacement fuse blows,
a short-circuit may be present and the product should be discarded.
o)
Read and follow all instructions that are on the product or provided with the product.
p)
SAVE THESE INSTRUCTIONS
TROUBLE SHOOTING (If Lights Do Not Work):
1. If entire tree does not light, make sure extension cord plug is securely inserted into a working
electrical outlet.
2. Check whether all bulbs are tightly fixed inside the lamp holder.
3. If a bulb is blown or broken, replace the faulty bulb according to bulb replacement instructions
below.
4. If the fuse in the power cord plug is blown, replace the blown fuse according to fuse replacement
instructions below.
5. If you are still experiencing problems with the tree please call us.
