Donaldson Torit Dalamatic Cased DLMC 1/2/15 страница 32 Скачать руководство пользователя

Страница: 32 / 36

Donaldson Company, Inc.

collector

rear panel

sealant

membrane

retaining frame

Membrex Explosion Membrane Replacement

Explosion Vent Membrane Replacement

Do not damage or pierce the

membrane during installation. A

damaged membrane will leak and fail.

1. Remove the bolts, flat washers, and hex nuts from

the retaining frame and set aside.

2.  Remove retaining frame and set aside.
3.  Remove the Membrex™ vent panel and discard.
4.  Clean old sealant and debris from the outside

surface of the grid panel.

5. Apply sealant to rear panel around bolt pattern.
6. Install replacement membrane realigning the

mounting holes carefully.

7. Reinstall the retaining frame using the hardware

removed in Step 1. Tighten hardware equally to

compress the sealant evenly.

Explosion Vent

Personal injury, death, and/or

property damage can result from

material discharge during venting.
The material discharged during the venting of

an explosion must be safely directed outdoors

away from areas occupied by personnel to

reduce risk of personal injury and/or property

damage.
The risk of personal injury and/or property

damage can be minimized or avoided by

locating vented equipment outside buildings

and away from normally occupied areas.
Explosion vents should be inspected regularly

to confirm physical and operational condition.

Replace any damaged parts immediately.
Standard explosion vents are intended for

outdoor installations only.

Remove all shipping materials,

including covers, from the

explosion relief vents prior to installation.

Failure to remove shipping covers will seriously

compromise explosion vent operation.

Unless otherwise noted, the explosion venting

calculations are based on formulas from NFPA-68 for

outdoor applications only, with no duct or obstructions

on the explosion vent panel.
Contact Donaldson Torit for assistance in calculating

specific venting requirements for equipment.
NFPA 68 can provide guidance on both the frequency of

and appropriate details for inspections.

Содержание Dalamatic Cased DLMC 1/2/15





































Результаты поиска

Содержание Dalamatic Cased DLMC 1/2/15

Отзывы:

Похожие инструкции для Dalamatic Cased DLMC 1/2/15

Бренды по названию

Популярные бренды

Donaldson Torit Dalamatic Cased DLMC 1/2/15, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Dalamatic Cased DLMC 1/2/15

Отзывы:

Похожие инструкции для Dalamatic Cased DLMC 1/2/15

Бренды по названию

Популярные бренды