Donaldson Torit Dalamatic Cased DLMC 1/2/15 страница 26 Скачать руководство пользователя

Страница: 26 / 36

Donaldson Company, Inc.

1/8-in NPT x 90°

male elbow

clean-air plenum pressure

tap location

1/8-in NPT adapter

plenum tap location

3/8-in flat washer

1/8-in NPT coupling

mounting bracket

#6-32 x 1/4-in mounting screws

support structure

mounting surface

Magnehelic gauge

high-pressure port

low-pressure port

two, 1/8-in NPT

adapters

plastic tubing

two, 1/8-in NPT pipe plugs

two, self-drilling screws

1/8-in NPT x 90° male elbow

dirty-air plenum pressure tap location

3/8-in flat washer

1/8-in NPT adapter

1/8-in NPT x 90° elbow

static pressure tee

Magnehelic Gauge Installation

Magnehelic

Gauge

The Magnehelic is a differential pressure gauge used

to measure the pressure difference between the clean-

air and dirty-air plenums and provides a visual display

of filter change requirements. The high-pressure tap is

located in the dirty-air plenum and the low-pressure tap

is located in the clean-air plenum.
1. Choose a convenient, accessible location on or near

the collector for mounting that provides the best

visual advantage.

2. Plug the pressure ports on the back of the gauge

using two, 1/8-in NPT pipe plugs supplied. Install two,

1/8-in NPT male adapters supplied with the gauge

into the high- and low-pressure ports on the side of

the gauges.

3. Attach the mounting bracket using three, #6-32 x

1/4-in screws supplied.

4. Mount the gauge and bracket assembly to the

supporting structure using two, self-drilling screws.

5. Thirty-five feet of plastic tubing is supplied and must

be cut in two sections. Connect one section of tubing

from the gauge’s high-pressure port to the pressure

fitting located in the dirty-air plenum. Connect

remaining tubing from the gauge’s low-pressure

port to the fitting in the clean-air plenum. Additional

tubing can be ordered from your representative.

6. Zero and maintain the gauge as directed in the

manufacturer’s Operating and Maintenance

Instructions provided.

Содержание Dalamatic Cased DLMC 1/2/15





































Результаты поиска

Содержание Dalamatic Cased DLMC 1/2/15

Отзывы:

Похожие инструкции для Dalamatic Cased DLMC 1/2/15

Бренды по названию

Популярные бренды

Donaldson Torit Dalamatic Cased DLMC 1/2/15, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Dalamatic Cased DLMC 1/2/15

Отзывы:

Похожие инструкции для Dalamatic Cased DLMC 1/2/15

Бренды по названию

Популярные бренды