Domino G Series Скачать руководство пользователя страница 53

Страница: 53 / 172

CONTROLLER ELECTRICAL SUPPLY

WARNING

Electricity. Risk of injury.

Turn off the equipment and disconnect the power supply before

disconnecting or making electrical connections.

When powered on, the controller contains live electrical components.

Physical contact with live electrical components can result in an electric

shock.

WARNING

Obstacle Hazard. Risk of Injury.

Do not install the equipment, cables, conduits or accessories in a

walkway, or in a location where they may cause an obstacle

hazard.

If the equipment, cables, conduits or accessories are installed in a

walkway, or in location where they may cause an obstacle hazard,

injury to personnel may occur.

CAUTION

Electricity. Risk of damage to equipment.

Turn off the equipment and disconnect the power supply before

disconnecting or making electrical connections.

When powered on, the equipment contains live electrical components.
An incorrect electrical connection can damage the equipment.

Connect the controller and electrical power adapter to a power supply using a suitable plug and

socket outlet. Make sure the power supply is accessible and close to the equipment, so it can be

quickly disconnected. If a fused power connector is used, fit it with a 5 A fuse. If a fused power

connector is not used, a circuit breaker or fuse rated at 5 A is required.
The supply must be free from electrical noise. Domino can give advice on suitable devices to

ensure trouble-free operation.
Only use the electrical power supply adapter listed below:

•

Manufacturer: MEAN WELL ENTERPRISES CO. LTD

•
•

Model: GST60A24

•

INSTALLATION

EPT077343 EN - Issue 1 - 11 November 2022

Содержание G Series













































































































































































Результаты поиска

Содержание G Series

Отзывы:

Domino G Series, Руководство по эксплуатации продукта, Страница: 53 / 172

Результаты поиска

Содержание G Series

Отзывы: