manualshive.com logo in svg

Domino G Series, Руководство по эксплуатации продукта, Страница: 3 / 172

Поделиться
Скачать
Domino G Series Скачать руководство пользователя страница 3

PREFACE PRODUCT MANUAL

This document, Domino Part No. EPT077343, is the official authority for the installation,

operation, maintenance and recycling of Domino G-Series Thermal Ink Jet units.
This document should be used to reinforce and complement any training program available with

the product. It is not designed to replace any such training program.
This product manual is the source document for all translated versions. It is the "Original

Instructions".
Domino will not accept any liability for damage to equipment or injury to personnel caused by

unauthorized or improper use of the Thermal Ink Jet equipment.
Only engineers trained by Domino should carry out repairs, adjustments or in any other way alter

settings or machine parts. Domino original parts shall always be used to ensure quality and

performance.
Users of this equipment are warned that it is essential to read, understand and act according to

the information given in Part 1: Health and Safety. This part of the document also specifies a set

of symbols which are used elsewhere in the document to convey special warnings or

requirements. It is, therefore, essential that users are also familiar with these symbols and act

accordingly.
It is important to:

•

Keep this document during the lifetime of the equipment.

•
•

Pass this document on to any subsequent holder or user of the equipment.

•

Preface Product Manual

EPT077343 EN - Issue 1 - 11 November 2022

3

Содержание G Series













































































































































































Отзывы:

Нет отзывов